Refine
Document Type
- Conference Proceeding (15)
- Article (7)
Language
- English (16)
- German (5)
- Multiple languages (1)
Has Fulltext
- no (22)
Is part of the Bibliography
- no (22)
Rolling mills are continually improved and opti-mized by implementing innovative technology to decrease costs and scrap. Despite of the progressive automation and experience, some important process parameters can still not be determined with sufficient accuracy. As part of the research project PIREF, the velocity of the hot rolled rod shall be measured by using im-pedance analysis to estimate the volumetric flow rate of the mate-rial. For a high accuracy measurement of the impedance, a pow-erful VNA is used. To minimize errors in the measurement, caused by e.g. temperature drift, a correction of the measurement fre-quency is needed. This must be achieved without recalibration of the VNA to avoid faulty behavior of the online control. To solve this problem, an approach based on a polynomial regression is presented in this work.
Velocity Approximation of Hot Steel Rods Using Frequency Spectroscopy of the Cross-Section Area
(2019)
In this work, an approach for velocity approximation of hot steel rods based on frequency spectroscopy is presented. For this purpose, a sensor already implemented in a rolling mill for measuring the cross-sectional area of the rolling stock is used to obtain information about the velocity of the hot rods. Moreover, the effect of forward slip is briefly discussed.
The development of innovative measuring technology for process optimization in hot rolling mills becomes more and more relevant because of increasing demands on product quality. Measurement technology for high-resolution non-contact cross-sectional area measurement has shown that the variation in cross-sectional area contains information about the rolling process. This information can be used for the development of new measurement devices and analytical methods for process optimization. The harsh environmental conditions and strict safety regulations result in great effort when implementing a new sensor prototype in hot rolling mills. For this reason, this work presents a mechatronic test stand that can simulate the cross-sectional area variation under laboratory conditions realistically.
Quality and dimensional accuracy of hot rolled steel rods depend on several process parameters. In fact many of these crucial parameters are not be sufficiently determined yet. By improving automation and process control costs and scrap of production can be decreased. As part of the research project PIREF, one of these parameters – the roll gap – is under investigation beside other topics. Before starting rolling, the roll gap is typically set to a fixed value according to the planed dimensions of the product, but the forces during the rolling of the rod cause an enlargement of the roll gap. In which way the rolls change their position and form shall be examined in our research project. Therefore a first experimental setup has been built up to determine the change in position of the rolls under applied force. This is realized by a pot core coil as sensor using impedance analysis. The first results are presented in this work as a proof-of-principle.
For the rod shape measurement of hot rolled round steel bars (rods) the high frequency eddy current method is especially well suited as it requires no contact point and is not limited to below the Curie temperature. Defects of the rod's shape can be detected by measuring the impedance spectrum of the RLC-oscillator. In the first laboratory setup an Agilent impedance analyser was used for initial tests. Nevertheless, this setup cannot be applied in a steel plant due to the difficult environmental conditions. Hence, a vector network analyser for passive impedance measurement that is applicable in these surroundings was developed.
Process Monitoring in Steel-Mills using Impedance Analysis: VNA Improvement for Data Acquisition
(2017)
The process automation extends over every manufacturing step of a product in the steel-mill to increase the quality, quantity and energy efficiency. The product dimensions are an important part of the quality control; these must maintain the specified tolerances. Additional to the cross-sectional-area, the measured data contains much more information about the manufacturing process, e.g. eccentricity, condition of the rolls and defects of the rod. For analyzing the measured data and to gather more information about the manufacturing process it is necessary to increase the speed of the data acquisition by performing some modifications of the VNA, e.g. faster analog to digital converter and microcontroller, improved firmware and optimized values of the passive electrical components for faster time constants and transient responses.
Bipolar electrosurgical systems are used for the treatment of benign prostatic hyperplasia (BPH) in urology. In order to analyse electrothermal processes during surgery the power loss density distribution around a bipolar resectoscope is calculated out of the measured potential distribution in isotonic saline solution ex situ. During further analysis power loss density values act as input for the Penne's bioheat equation. To achieve results, which are as realistic as possible, a method to obtain power loss density values, depending on the observed tissue or medium in the operating field, is presented. Applying this method, the power loss density distribution in isotonic saline solution at 25 °C is compared to the distribution calculated for the average conductivity of biological tissue in the region of interest.
Process diagnosis is an important method for improving product quality in rolling mills. In addition, the measurement of process variables such as roll gap, cross-sectional area, velocity, and volume flow of the material during production enables the implementation of model-based control concepts to improve product quality. The non-contact speed measurement of hot wire and bar is still a big challenge due to the rough environmental conditions and is solved mainly with optical measuring methods in production. The alternative measurement principle with eddy current sensors presented in this paper enables velocity measurement at locations in a rolling mill where optical measurement methods are not suitable.