621.3 Elektrotechnik, Elektronik
Refine
Year of publication
Document Type
- Conference Proceeding (22)
- Article (18)
- Book (2)
- Part of a Book (2)
- Doctoral Thesis (1)
- Part of Periodical (1)
Language
- English (24)
- German (19)
- Multiple languages (3)
Has Fulltext
- no (46) (remove)
Is part of the Bibliography
- no (46)
Keywords
- Halberzeugnis (1)
- Hochtemperatur (1)
- Inprozesskontrolle (1)
- Rundstahl (1)
- Warmwalzen (1)
The development of innovative measuring technology for process optimization in hot rolling mills becomes more and more relevant because of increasing demands on product quality. Measurement technology for high-resolution non-contact cross-sectional area measurement has shown that the variation in cross-sectional area contains information about the rolling process. This information can be used for the development of new measurement devices and analytical methods for process optimization. The harsh environmental conditions and strict safety regulations result in great effort when implementing a new sensor prototype in hot rolling mills. For this reason, this work presents a mechatronic test stand that can simulate the cross-sectional area variation under laboratory conditions realistically.
Process diagnosis is an important method for improving product quality in rolling mills. In addition, the measurement of process variables such as roll gap, cross-sectional area, velocity, and volume flow of the material during production enables the implementation of model-based control concepts to improve product quality. The non-contact speed measurement of hot wire and bar is still a big challenge due to the rough environmental conditions and is solved mainly with optical measuring methods in production. The alternative measurement principle with eddy current sensors presented in this paper enables velocity measurement at locations in a rolling mill where optical measurement methods are not suitable.
Velocity Approximation of Hot Steel Rods Using Frequency Spectroscopy of the Cross-Section Area
(2019)
In this work, an approach for velocity approximation of hot steel rods based on frequency spectroscopy is presented. For this purpose, a sensor already implemented in a rolling mill for measuring the cross-sectional area of the rolling stock is used to obtain information about the velocity of the hot rods. Moreover, the effect of forward slip is briefly discussed.
In the field of producing hot-rolled steel bars and wires, hot rolling mills are incomplete or barely equipped with measuring technology for recording relevant process parameters. Therefore, there is a big potential to increase product quality and to decrease costs and scrap by improving process control establishing new sensor systems. One of these crucial parameters is the roll gap,which is investigated as part of the research project PIREF. In this paper an experimental setup for examining the roll gap during a rolling process is presented and based on these results different sensor arrangements are discussed.
Quality and dimensional accuracy of hot rolled steel rods depend on several process parameters. In fact many of these crucial parameters are not be sufficiently determined yet. By improving automation and process control costs and scrap of production can be decreased. As part of the research project PIREF, one of these parameters – the roll gap – is under investigation beside other topics. Before starting rolling, the roll gap is typically set to a fixed value according to the planed dimensions of the product, but the forces during the rolling of the rod cause an enlargement of the roll gap. In which way the rolls change their position and form shall be examined in our research project. Therefore a first experimental setup has been built up to determine the change in position of the rolls under applied force. This is realized by a pot core coil as sensor using impedance analysis. The first results are presented in this work as a proof-of-principle.
Rolling mills are continually improved and opti-mized by implementing innovative technology to decrease costs and scrap. Despite of the progressive automation and experience, some important process parameters can still not be determined with sufficient accuracy. As part of the research project PIREF, the velocity of the hot rolled rod shall be measured by using im-pedance analysis to estimate the volumetric flow rate of the mate-rial. For a high accuracy measurement of the impedance, a pow-erful VNA is used. To minimize errors in the measurement, caused by e.g. temperature drift, a correction of the measurement fre-quency is needed. This must be achieved without recalibration of the VNA to avoid faulty behavior of the online control. To solve this problem, an approach based on a polynomial regression is presented in this work.
Process Monitoring in Steel-Mills using Impedance Analysis: VNA Improvement for Data Acquisition
(2017)
The process automation extends over every manufacturing step of a product in the steel-mill to increase the quality, quantity and energy efficiency. The product dimensions are an important part of the quality control; these must maintain the specified tolerances. Additional to the cross-sectional-area, the measured data contains much more information about the manufacturing process, e.g. eccentricity, condition of the rolls and defects of the rod. For analyzing the measured data and to gather more information about the manufacturing process it is necessary to increase the speed of the data acquisition by performing some modifications of the VNA, e.g. faster analog to digital converter and microcontroller, improved firmware and optimized values of the passive electrical components for faster time constants and transient responses.
Editorial
Jörg Himmel, Olfa Kanoun, Thomas Seeger, Klaus Thelen IEEE Workshop on Industrial and Medical Measurement and Sensor Technology – SENSORICA 2016 1
Beiträge Jan Taro Svejda, Andreas Rennings, Daniel Erni A metamaterial based dual-resonant coil element for combined sodium/hydrogen MRI at 7 Tesla 2
Fabian Feldhaus, Ingo Schmitz, Thomas Seeger Emission spectroscopy based sensor developed for engine testing 13
Anne-Sophie Rother, Thomas Dietz, Peter Kohns, Georg Ankerhold Molecular laser-induced breakdown spectroscopy for elemental analysis 23
Johannes Kiefer, Andreas Bösmann, Peter Wasserscheid Quantitative measurement of complex substances dissolved in an ionic liquid using IR spectroscopy and chemometrics 32
Oliver Gieseler, Hubert Roth, Jürgen Wahrburg Methods to determine the scaling factor in X-ray images for exact preoperative planning in hip surgery 38
Erwin Gerz, Matthias Mende, Hubert Roth Development of an optical tracking system for a novel flexible and soft manipulator with controllable stiffness for minimal invasive surgery (MIS) 47
Jens Weidenmüller, Christian Walk, Özgü Dogan, Pierre Gembaczka, Alexander Stanitzki, Michael Görtz Telemetric multi-sensor system for medical applications – The approach 53
Inga-Maria Eichentopf, Martin Reufer Measurement and analysis of wavefront structures of diode lasers 59
The detection of soil erosion processes in dams, hydraulic heave failure or corrosion processes of reinforcing steel in concrete are a small selection of measuring applications in civil engineering where the impedance analysis can be used to determine the measurand. Those measuring applications are having high requirements for the measuring hardware. For example a common interface for fast data exchange, high resolution, independent functionality and easy customizability to suit the measuring application. For that reason, a well-known application for steel-mill process monitoring can be used as a development platform. This hardware platform is based on a vector network analyzer and is meeting the requirements mainly. However, a couple of modifications has to be made, like replacing the ADC for a higher sample rate, Ethernet for easy and fast data exchange and the microcontroller for more calculation power.
Gallium Nitride (GaN) and Indium Gallium Nitride (InGaN) have become important semiconductor materials for the LED lighting industry. Recently, a photoluminescence (PL) technique for direct in-situ characterization of GaN and InGaN layers during epitaxial growth in a planetary metalorganic vapor phase epitaxy (MOVPE) reactor was reported. The PL signals reveal – at the earliest possible stage – information about current layer thickness, temperature, composition, surface roughness, and self-absorption. Thus, the PL data is valuable for both controlling and optimizing the growth parameters, thereby promising both better devices and a better yield for the LED industry. This technical report describes an extension of this PL technique to close coupled showerhead (CCS) reactors with narrow optical viewports. In contrast to the wide aperture optics in previous investigations, a compact and all-fiber optical probe without voluminous lens optics, filter elements or beam splitters was used.